If anyone needs it, it's a simple matter of reverting this
basic commit.

This is hack-level development.

With this commit you can do UDP DL traffic of say 100Mb/s over
a 5MHz link with one connected UE and the eNB should not crash
because of memory exhaustion. Of course on the receiver side
you won't get 100Mb/s and many many lost packets. But the system
should not crash. 1Gb/s does not work. So in any case try to
remain within some reasonable limits. There is no reason to
push more than twice the maximum achievable throughput of
the link.

This work is based on a patch proposed by Francesco Gringoli.

Not sure that the use of __KERNEL__ is the correct solution.
To be checked at some point.

After this commit, the following works:
./build_oai --UE -c

Fix #582, RTAI, RTAI_ENABLED, ENABLE_RTAI_CLOCK, RTAI_ISNT_POSIX, _RTAI_MATH_H, CELLULAR, TIMER_ONESHOT_MODE, EMOS, EMOS_CHANNEL, OAI_EMU, OPENAIR_EMU, PHY_ABSTRACTION, PHY_ABSTRACTION_UL removed

This commit fixes issues introduced by the previous commit.

Summary of work:
- cleanup:
  - fix LOG_XX to be less verbose
  - fix cmake_targets/CMakeLists.txt
  - fix oaienv
  - remove dead code
- bug fixes:
  - in openair1/SCHED/fapi_l1.c we had:
      eNB->pdcch_vars[subframe&1].num_dci           = number_dci;
    should be:
      eNB->pdcch_vars[subframe&1].num_dci           = 0;
    This bug let the PHY send more DCIs than what should have been
    sent because num_dci is incremented later on in the code.
    This fix may be a problem for fapi mode, to be checked.
  - add new T VCD traces
  - revert openair1/PHY/TOOLS/file_output.c to 'develop' version
  - remove thread_id in logRecord/logRecord_mt
  - revert (and adapt) configuration files
  - be careful when doing frame++, we need to % 1024
  - revert target_rx_power in openair2/LAYER2/MAC/eNB_scheduler_ulsch.c
- NFAPI:
  - the open-nFAPI code has been included in the repository. See nfapi/README.
    Maybe we should "git clone" the Cisco repository instead. We have to be
    careful of availability though.

What has been tested:
- monolithic eNB FDD 5/10MHz with one UE, iperf UDP/TCP uplink/downlink

Anything else may fail to work, especially the FAPI mode, which has not
been tested at all.

- when exiting task, the task is set as "not configured"
- this permits to start a task again

Sometimes when the user does ctrl+c to quit, it may not quit
if nothing comes on the socket. Closing the socket in the
signal handler fixes this.

Do not link the X stuff for tracers not needing it.

Later on, use this file with gtkwave.
To be used to check realtime behaviour of the system.

This tracer extracts output subframes generated by the eNodeB,
so they can be analyzed with some external tools.

This tracer extracts the content of a buffer field of an event
that was previously saved using the tracer 'record'.

For example, to extract the channel estimation done in
frame 924 and subframe 2 as saved in the file input_record.raw
and to store it in the file output.raw, do:

./extract -d ../T_messages.txt -o output.raw input_record.raw ENB_PHY_UL_CHANNEL_ESTIMATE chest_t -f frame 924 -f subframe 2

- UE_id 0 is for rnti 65535 (sib)
- UE_id 1 is for rnti 65534 (this is a hack)
- UE_id 2 is for rnti 2     (RA RNTI as of today's code/config)
- we start enb by displaying UE_id 3
- there was a bug: we need to lock when resetting UE ids (reset_ue_ids)

removal of LOG_I put for debugging.